[Solved] Skoda 1.9 TDi P0321 16705 G28 Sensor Implausible Signal Fault Code

I recently experienced and fixed the P0321 / 16705 fault code on my Skoda Fabia VRS 1.9 TDI with the PD130 BLT engine. This engine is the extremely common VAG PD 1.9 turbo charged diesel engine as used in many models of VW/Audi/Skoda.

During diagnosis of this problem I did a lot of research concerning the P0321 fault code which is for the G28 engine speed sensor implausible signal which I thought I would share, as well as what the final solution to the problem was.

The ross-tech wiki lists the following information regarding this code:

P0321 / 16705 fault code information

Possible Symptoms

  • Engine shuts off
  • Engine doesn't start
  • Speedometer inoperative
  • Glow Plug Indicator Lamp (K29) flashes

Possible Causes

  • Engine Speed Sensor (G28) loose
  • Engine Speed Sensor (G28) faulty

Possible Solutions

  • Check Engine Speed Sensor (G28)

Special Notes

  • The Engine Speed Sensor (G28) is also used as a reference sensor for the crankshaft position and correlates with the Camshaft Position Sensor Bank 1 (G40) and Camshaft Position Sensor Bank 2 (G163).
  • When an engine will not start due to mechanical (spark/fuel/compression/timing) related issues it is not uncommon to set a false G28 fault codes due to extended cranking with a no-start condition.

My symptoms:

  • The car would not rev above approximately 3400rpm
  • If you tried to rev over 3400rpm the limiter would cut in and it would trigger the 16705 fault code.
  • This fault code would illuminate the check engine management light and also flashing glow plug light.
  • Once the fault code was triggered you would not rev over approx 3400rpm.
  • If you did not rev over 3400rpm you could drive the car as normal.
  • Car would start without hesitation hot or cold.
On these engines the ECU uses the values from the G28 crankshaft position sensor and G40 camshaft position sensor to determine crank angle relative to camshaft angle. In VCDS this is known as torsion value or syncro angle.

Because the ECU looks at the relationship between these two values, if one value is implausible then it will struggle to tell which sensor is at fault. In my case it is suggesting that the value from the G28 sensor does not match the value from the G40 sensor.

The fault code first appeared after I had the timing belt changed and I also changed the thermostat. 

As this issue is related to timing my first thoughts were that it was something to do with the timing belt change. Perhaps the timing was not correct or the belt tension was wrong or the camshaft sensor had been knocked during the work.

Looking into this further I removed the top timing belt cover and checked the timing belt tension as well as the little tabs which are on the engine side of the camshaft pulley - these are used by the G40 sensor and if one of them was bent this might prevent the sensor from reading the position correctly. No problems found.

I also read the syncro angle using VCDS and it was fluctuating between -1.1KW and -1.7KW which is within range - this rules out the timing being incorrect.

I also had to change the thermostat around the same time. The thermostat on this engine is on the front of the engine to the left hand side which is close to where the wire for the G28 crankshaft sensor runs from the plug at the top to the sensor position at the bottom under the oil cooler.

Solution


In the end the G28 crankshaft sensor was faulty and I think it was caused by coolant running down the cable sheath and going directly into the sensor itself...or it could just be a coincidence.

Once the G28 sensor was replaced with a genuine VW item the issue was cured completely.

1.9 tdi blt G28 crankshaft sensor behind oil cooler
G28 crankshaft sensor location behind oil cooler
G28 sensor highlighted in red



Mazda MX5 NA Replacing Broken Corroded PPF Ground

If you are experiencing any sort of electrical or starting issues it is always worth checking all your grounds or earth straps as they are also known.

On the Mazda MX5 there is an important earth on the PPF which provides a really strong connection to the engine block. Due to this earth location being low to the ground it is fairly common to find this connection badly corroded or even snapped completely (see below).


If you want to replace this PPF ground strap entirely then this is the spec:
  • Length: 1500mm
  • Size: 16mm² 
  • 6mm ring lug terminals on both ends


When replacing the cable it is a good idea to give the area on the PPF a good clean to remove any corrosion and ensure a solid collection. I used a wire drill bit attachment to do this.

Then it's just a case of feeding the cable through the grommet and into the boot. At the battery end I simply bolted the new cable on top of the original connection. Secure with cable ties to stop chaffing.


[SOLVED] How much do Mazda MX5 baby teeth/tie down hooks weigh?

mazda mx5 tie down hooks baby teeth
You may have noticed the two ugly looking (probably rusty by now) "tow hooks" pointing out the front bumper of your MX5 NA.

These are not actually tow hooks but tie down hooks used for securing the cars when they were being shipped from Japan to different countries.

They have affectionately been nicknamed the baby teeth by Miata enthusiasts partly due to them kind of looking like teeth sticking out the front bumper, and partly because many see it as a right of passage for owners to "pull them out" when they first get their MX5.

weight of mazda mx5 baby teeth
The weights of the tie down hooks are often exaggerated so here are the definitive weights for both front and rear tie downs as I have just removed them from my car.
  • Front tie down hooks: 1.3kg
  • Rear tie down hooks: 1.5kg
  • Both front and rear combined: 2.8kg
The weight might vary within a few grams depending on how rusty they are. :-D

Should you remove the baby teeth?
Will you notice that kg, no, but as far as weight saving goes on cars, it's a very easy win at no cost to comfort or practicality. Probably the easiest 2.8kg you will ever save...

Some people use the baby teeth to tow the car, so bear this in mind if you do decide to remove them. However this is not what they are designed for and Mazda do not recommend using them for this purpose.

In my opinion the front bumper looks much better without the tie down hooks sticking out, especially if they have gone rusty.

How to remove MX5 Miata baby teeth?
The front baby teeth are held in place by three bolts on each tie down hook, these can be reached by turning the wheels to full lock and then reaching in from the wheel arch. As you would expect, they are likely to be rusted so it's advisable to soak with a penetrating oil before as it can be awkward to get a good angle for putting a lot of force through the spanner.

The rear are held by two bolts (I think) and can also easily be removed without needing to jack the car up.

[Guide] Fitting Running/Side Marker Lights To Mazda MX5 NA

Mazda mx5 side marker lights

Fitting running/side marker lights to your Mazda MX5/Eunos Roadster is a subtle mod to make your car stand out a bit and increase visibility to other road users, it's also ridiculously easy to do yourself even if you have never worked on car electrics before.

US spec cars have orange running lights in the front and red running lights in the rear, however UK and JDM spec MX5's have reflectors instead.

Fortunately for us it's very easy to fit bulbs in these reflectors and wire up the side marker lights to be come on with the side lights.

Tools needed:
  • Cross head screwdriver
  • Wire strippers/cutters
  • Crimping tool
  • Drill
  • Large flat head screwdriver
  • Pliers


Parts needed:
  • 2 x 501 (W5W) bulb holders
  • 2 x Amber 501 bulbs
  • 4 x Cable Lock (Scotch Lock) Connectors
  • 4 x Butt connectors
  • 2 x cable ties
  • Electrical tape
  • 8amp wire

Step by step guide
Remove side reflectors and make hole in the rear to fit bulb holders. To remove them just undo the two phillips screws on either side and then gently pry out.

mazda mx5 side marker reflectors

The only difference between the UK and US side reflectors is that a hole was not made in the rear. So all we have to do is make that hole.

501 w5w bulb holder

Use something to measure the diameter of the bulb holders so you know how big to make the holes. The plastic is very soft so go slowly and no need to put much pressure on the drill, you don't want to fly through and damage the lens.


My bulb holders were about 13mm and I didn't have any drill bits that big, so I just went as big as I could and then gradually increased the size of the hole with various flat head screwdrivers. This worked very well as the plastic on the rear of the side marker is very soft.


You want a nice tight fit so the bulb holder doesn't fall out and water and dirt can't get in. You can secure the bulb holder with silicone or similar but I wanted to make it easy to change the bulbs so chose not to do this.

Remove sidelight/indicator unit and thread wire through to wheel arch

Mazda mx5 Miata side light wiring

Again just two phillips screws to remove the sidelight, both bulb holders twist to unlock.


Pop up your headlights and there's a few holes to feed the wires down into the wheel arch directly under the headlight. I routed the new wires under some of the original wiring to keep it tidy and stop it from flapping around.

Fit cable lock connectors to positive and ground from the side light


The good thing about the cable lock connectors (also known as scotch locks) is that you do not need to cut any wires to tap into the connection. Watch out that both wires are centred in the connector to ensure a good connection is made.

Connect bulb holder to new wiring


The 501 bulb holders that I bought came with approx 7cm of cable so this needed to be connected to the new cable I just installed. To do this I used bullet connectors from Halfords as a temporary measure however I am intending to solder and shrink wrap this connection as that is a more permanent solution.

Fit amber bulbs and refit reflectors


You want to check at this point that everything is still working as it should. Sometimes the scotch lock connectors can be a bit temperamental. So give everything a good wiggle and tug to make sure it's not going to lose a connection as soon as you go over a pothole.

Secure wire with cable ties


Your bumper should have this bracket in it which is ideal for securing the wires to stop them flapping around in the wind.

You're done



Like this guide? Spotted that i've done something really dumb? All comments welcome below.

Mazda MX5 MK1 [Tall People Mods] Remove Clutch Foot Rest Pedal


I wouldn't be the first one to praise the Mazda MX5 NA for being a great drivers car, nor would I be the first one to comment on it's lack of cabin space...

I'd actually wanted an MX5 for a while, but being 6ft 5in (195cm for you non-backwards readers) it was always debatable whether I would actually be able to fit in the thing.

Fortunately I took the plunge and although things were a little tight, with a few small mods I am very* comfortable and importantly can turn the wheel 180 degrees without hitting my knees.

*ish

This post is about removing the clutch foot rest pedal, which was one of the easiest, cheapest and most effective mods I made to get more leg room in my MX5.

The clutch rest pedal is pretty much exactly what it sounds like - it sits to the left of the clutch pedal and it's purpose is for you to rest your foot on when cruisin'.


Unfortunately for us tall drivers, it also takes up a load of valuable leg space.

Fortunately, it is only held in place by 2 x 10mm fixings.

Removing the clutch rest pedal will leave 2 threaded studs rising up from the floor which are a bit uncomfortable as you can feel them through your shoes. It's also nice to have a flat platform to brace against when cornering.

Two options:
  1. Grind them off
  2. Fix something over them

I went with option 2 as I want to be able to put the pedal back in when I sell the car. I had some bits of wood in the shed and thought that'll do...

The mounting studs are only about 15mm long which is why I had to sink the holes slightly so the nuts could get a bite on the thread.

Side shot shows just how huge the plastic dead pedal is compared with my delicately hand-crafted replacement.


Doesn't exactly look fantastic but this was just a test fit and I wasn't sure if I was going to keep the mod.

This summer I might paint it black and then stick some grip tape or similar on the front face to make it blend in more.


At first it feels a little strange as you have to lift your foot more to press the clutch rather than slide over to it, however after a couple of hours driving you will completely adapt to it.

More Mazda MX5 tall people mods coming soon...

Please let me know in the comments if you found this helpful and also any other recommended mods for tall drivers of MX5 Miatas.

VW MK5 Golf GTi TFSI Brake Booster Hose 1K0 612 041 GM Information


This is just a short post to help anyone else out and save them doing the research I had to.

The brake booster hose connects directly to the vacuum pump as part of the system to give power assisted braking. There is also a check valve which prevents boost from going into the vacuum pump.

Over time the hoses can become brittle and start to crack around the connections, the plastic check valve also becomes brittle and can be easily damaged when working on the car.

Failures of this part can result in several symptoms:

  • Loss of power braking assist
  • Check valve failing to close resulting in loss of boost pressure
  • Idle and vacuum issues

Side note: The short rubber hose between the check valve and the inlet is a popular place to take a boost tap from to operate a boost gauge or vacuum operated diverter valves such as the Forge Recirculating Valve (FMFSITVR ).

VW part numbers:
  • Original part number: 1K0 612 041 BM (shown below without extra vacuum nipple)
  • Superseded part number: 1K0 612 041 CH (also without extra vacuum nipple
1K0612041BM brake vacuum hose
1K0612041BM brake vacuum hose
  • Latest part number: 1K0 612 041 GM (as shown below with extra vacuum nipple)
If you car does not have a pipe for the vacuum nipple (e.g. AXX) then you can just block this off, the genuine part number for this is 056 129 777 which looks like a mini green traffic cone.
1K0 612 041 GM latest part number. Photo owned by ECSTuning.com

VW Mk5 Golf GTi (TFSI) Misfire When Engine Is Warm

This post summarised for anyone in a rush...

Car
  • 2005 VW MK5 Golf GTI 2.0 (AXX engine)

Symptoms
  • Slight misfire on idle when engine is warm
  • No symptoms when engine is cold

Fix
  • New coil pack for cylinder 1


More information


I recently sold my 2005 Honda Civic Type R (EP3) and bought a 2005 VW Mk5 GTI in the hope of moving to something a little more torque-y and refined.

I was going through that first month or so of owning a new used car which I hate with a passion. You know, when you're constantly thinking:
  • Have I bought a lemon?
  • Was that a knock?
  • Is that sound normal?
  • Is the engine going to explode
Well anyway, during that enjoyable period I noticed that when the car was up to temperature it would slightly stumble occasionally on idle, most "non-car" people wouldn't have noticed it, but anyone into their motors would.

I did not experience any hesitation or loss of power, but after scaring myself with stories of compression loss and head gasket failure I decided the first sensible option would be to change the coil packs and spark plugs.

So I ordered the following parts:
  • Genuine VW coilpack - 07K 905 715 G (previous revision 07K905715F)
  • Bosch spark plug - 101 905 631 H (Bosch part number: FR5KPP332S)
Before I had a chance to fit these the misfire got much worse and finally conked out and wouldn't run at all.

Luckily I had an OBDII bluetooth adapter and Torque for Android which enabled me to read the OBDII fault codes to get a better idea of what was going on.

OBD Scan Result: 
  • P0300 - Random/Multiple Cylinder Misfire Detected
  • P0301 - Cylinder 1 Misfire Detected
  • P0302 - Cylinder 2 Misfire Detected
  • P0351 - Ignition Coil A Primary/Secondary Circuit
Coil A = Cylinder 1 so at least that seemed consistent. However, still not conclusive that this is a coil or spark plug issue.

I changed the spark plugs first but this made no difference. The old plugs and coils were pretty filthy though with lots of corrosion build up pretty much everywhere where you don't want corrosion build up.
bad bosch spark plugs from golf mk5 gti

After changing the coil pack on cylinder 1 the engine fired straight up and the misfire disappeared.

Problem solved.

Cleaning Cloudy/Foggy Car Headlights With Bar Keepers Friend

before and after cloudy headightsCloudy car headlights not only look bad, but they are also dangerous for two reasons:
  1. Reduces the amount of light which makes it out of the headlights and onto the road, where you want it.
  2. It impairs the all important scattering of the beam, causing glare for other road users.
It is possible to fail an MOT for cloudy headlights as it ruins the light scattering. A local garage tried to charge us £60 just to clean our cloudy headlights so it's well worth looking at alternative methods and doing it yourself!

There are many ways of cleaning headlights which have gone foggy and using Bar Keepers Friend is just one of them which I have used with good success so I thought I would share.

Bar Keepers Friend vs. Brite Powder Power

To avoid confusion from my photos, Bar Keepers Friend recently re-branded to Brite Powder Power, so they are exactly the same product, just a different label.

Bar Keepers Friend is a more familiar brand which has been around for quite a while and has many uses around the home including cleaning kitchen pans, toilets and as covered in one of our previous posts, it is also excellent at cleaning car windscreens.

How to clean your headlights

Cleaning cloudy car headlights with Bar Keepers Friend (Brite Powder Power) is very quick and easy and in a few minutes you will have lovely clear headlight lenses again.

The advantage of using this method to restore headlights instead of wet sanding them is that Bar Keepers Friend does not scuff up the lenses so much that you need to polish them back clear again.

For really badly clouded headlights it may not be enough but for the price of Bar Keepers Friend on Amazon (£3.10 with Free Delivery) it's certainly worth a go. If you are not a fan of Amazon then it is also available on eBay. N.B I have had to buy this a couple of times in the past and it was not readily available in local shops so I had to purchase online.

Required

  • Polishing pad or cloth
  • Bucket of water
  • Bar Keepers Friend

Step-by-step guide

Step 1. Lightly wash the headlights and surrounding area with the polishing cloth and water
This is just to remove any grit which might be sitting on the headlights. Even though the plastic used in headlights is generally very hard-wearing, you don't want to risk accidentally creating scratches in the lenses or paintwork around the headlights when you rub in the Bar Keepers Friend.

Step 2. Pour a small amount of the Bar Keepers Friend onto the damp polishing pad and work into the headlight lens. The moisture from the polishing pad will turn the powder into an abrasive paste and you should be able to feel that it is rough against the headlight lens.

You should apply a good amount of pressure and polish in a circular motion being very careful to avoid touching the paintwork as this could mark your paint.

Depending on how badly fogged your headlights are this could take up to 15 minutes of constant polishing for each headlight and you will need to re-apply the powder to the polishing cloth every couple of minutes. Who said saving money would be easy?

Step 3. Once you are satisfied that the headlights have been restored then you need to gently wash all the powder residue from around the headlights and bodywork. This is easily done with some water and sponge.

Step 4. Stand back and admire you restored car headlights.

Tried this out and impressed (or unimpressed) with the results? Please leave your comments below.

restored car headlights


Why does my car squeal?

If you are wondering why your car is making a squealing noise then this quick guide should help you find the cause of the squeal. Don't let it annoy you any longer...

99% of high pitched squealing noises from cars are likely to be caused by either:
  1. Fan belt
  2. Brakes
Identify the cause of the squeal
When the engine is cold and the car is parked, open the bonnet and then start the engine. The fan belt is often located on the left side of the engine and you should be able to see it moving when the engine is running.

Listen for noise coming from this area, particularly when the belt is under extra load.

You can put extra load on the fan belt in a few different ways depending on your particular model of car:
  • Increase the engine revs
  • Put the alternator under load e.g. turn on full beam headlights, heated rear windscreen etc.
  • Turn on the air conditioning
  • Turn the steering wheel to full lock and then back again
Cars most often squeal after the car has been left overnight, particularly if it is damp - this is because the alternator is putting extra load on the belt as it's trying to re-charge the battery and also dampness can reduce grip, causing the belt to slip.

If you can hear the squealing noise when the car is stationary, then the problem is probably your fan belt (also known as alternator belt, aux belt or accessory belt) and you should check out our guide on how to fix it.

A worn fan belt on a Honda Civic Type R
If you cannot hear the squeal noise when the car is parked with the engine running then it is quite likely that the noise is related to your brakes. Go for a drive with the windows down and determine if it happens when you are driving or only under braking.

Unless you have a seized brake caliper then any squealing is only going to occur when you apply the brakes to slow down. If you car squeals when you apply the brakes then I would strongly recommend taking it to a professional.

How to Solve That Squeaky Fan Belt Noise

squeaky fan belt noise
A worn fan belt on a Honda Civic Type R
Fed up of that annoying squeal from your fan belt every time you start the car? Yep me to. That's why I wrote this article.

Luckily, the most common cause of squealing is the auxiliary belt/fan belt which can normally be fixed relatively easily by the home mechanic, the good news is that even if you do have to take the car to a garage, the cost is likely to be low. Before calling a garage, make sure you read our blog post all about the causes of squeaky/squealing fan belts and how you might be able to fix the problem by yourself for free!


Fan belt vs alternator belt vs auxiliary belt vs serpentine belt vs vs accessory belt
Confusing eh? 99% of the time these terms are all referring to the same thing, which is a belt powered by the engine to drive auxiliary components such as the cooling fan, alternator, power steering pump or air conditioning compressor.

To minimise confusion, for the rest of this article I will refer to this belt as the 'fan belt'. One because that's what most people still tend to call it, and two because it's quicker to type. ;-)

Why does the fan belt squeal?
The squeal/squeak noise is caused by the fan belt slipping on the pulleys. There are several possible reasons for why this happens.

When electrical load is applied to the alternator (e.g. turning the steering wheel in a car with electric power assisted steering) it takes more force to turn and so there is a greater amount of friction the fan belt must overcome to turn which makes it more likely to slip.

Fan belts are designed with V shaped grooves which run the entire length of the belt. This allows the belt to slip a certain amount, this is because the load on the accessories driven by the fan belt can suddenly increase, and without this ability to slip then they would likely snap.

You are more likely to hear that annoying squeaky noise on damp mornings if the car has been left overnight. This is because the dampness can cause the belt to have less grip and also because if it's cold, the alternator will have more load on it.

Five possible causes:
  1. Worn fan belt
  2. Incorrect fan belt tension
  3. Oil leak in engine bay
  4. Seized components driven by the belt
  5. Pulleys/components are out of alignment

1. Worn fan belt
Fan belts are made with rubbers which degrade and glaze over time. Moisture, oil and heat cycles all contribute to this process and once the belt is glazed it is more likely to slip and cause that annoying squeal sound.

2. Incorrect fan belt tension
Quite simply, if the belt is too lose it will 'slip' on the pulleys which will cause that annoying high pitched squealing noise.

A crude way to test the tension of the belt is to press on the belt between two pulleys with your thumb - you should get about 1/2 inch of deflection. This should give you a rough idea of whether your fan belt is tensioned correctly.

Depending on what car you have, the tension of the fan belt will either be set manually or by an auto adjusting tensioner.

If the tension can be manually adjusted then refer to a Haynes manual or similar to find out how to carry out this procedure.

If your engine uses auto adjusting tensioners then these should be replaced along with the fan belt.

3. Oil leak in engine bay
If your fan belt belt or the various pulleys which it runs through become contaminated with oil, even just a fine mist coating, this will reduce the grip the belt has and will cause it to slip and squeal more than usual.

Oil leaks in the engine bay are more likely to occur on engines with a turbo because any small leaks in the intake system or intercooler pipework (which are under pressure on boost) are likely to spray fine droplets of oil all over your engine bay.

To rectify this problem you need to find and fix the oil leak (which can be easier said than done) and then replace the fan belt being sure to also clean any pullies, tensioners and guides to remove any oil residue.

I have also heard of 'other fluids' such as power steering fluid or coolant causing belts to slip so it is worth checking for leaks from the reservoir as well.

4. Seized components driven by the belt
If the alternator bearings or any of the pulleys are seized/sticky then this could cause the belt to slip simply because it is creating more drag than the belt can handle.

5. Pulleys out of alignment
If the belt guides are out of alignment the belt cannot sit properly and will cause a noise. Normally, fan belt noises which are caused by misalignment of the pulleys will be more of a chirping noise than a squeal.


Fixes
Before spending money on new belts or professionals, the cheapest and easiest thing to try is cleaning the belt and pulleys with carb cleaner or even a mild detergent mix. In some cases the slipping belt is caused by contamination from oil or other fluids from the engine bay and simply cleaning this off will stop the noise. In any case cleaning the belt and pulleys should help increase friction slipping and causing that irritating squeaking sound.

One diagnosis method is to spray a bit of water on the ribbed side of the belt when the engine is running and making the noise. If the noise stops then this is likely cause by an alignment issue. If the noise gets worse then it is likely a friction issue.

Please feel free to leave any comments or tips you might have for other readers below.

[Solved] Honda Civic both headlights not working on dipped beam

I turned the headlights on my 2005 Honda Civic EP3 Type R to drive home the other evening and both bulbs went out after about half a second on dipped beam. Strangely, main beam was still working perfectly.

Full symptoms:
  • Dipped beam not working for both headlights
  • Full beam working as normal
  • Sidelights working as normal
  • Dash lights working as normal when combination light switch is toggled to the dipped beam position
Great, I thought, what were the chances of both bulbs going at the same time? I always jump to the worst case scenario and assumed the alternator must have surged and blown both bulbs, or I was going to be cursed with some nightmare intermittent electrical fault requiring hours of diagnostics (electrics isn't my strong point).

At best I thought I was going to have to try and track down a blown fuse or relay.

So I started looking through my service manual and found the Honda Civic Type R headlight circuit diagram.

Headlights circuit diagram

Click to expand
There is some misinformation online, where people are posting that the fuses are separate for main and dipped beam, but what this diagram clearly shows is that the right and left headlights each have their own relay and fuse which "control" both main and dipped beam.

So the fuses and relays are split into the right and left headlight, rather than dipped and main beam - from a safety perspective this makes perfect sense as you wouldn't want to be driving down a country lane and have a fuse blow which wipes out dipped beams on both sides would you?

The good news is that this eliminated the relays and fuses as the cause of the fault, as if either of them had gone then full beam would not be working in the affected headlight either.

On the next probable culprit - the combination light switch aka the 'stalk' on the steering wheel which controls.

Faulty combination switch on Honda Civic
After some googling, I found that lots of owners have reported faulty combination switches and I believe there was even a recall in America for them. Basically the terminals get corroded and don't make a connection when you

Luckily, it looks quite easy to remove the combination switch to test it:
  • Remove 3 x screws holding lower steering wheel surround in place
  • Separate from upper steering wheel surround
  • Remove 2 x screw from on front of combination switch to allow it to be removed from the steering column
However, I didn't have to do that as I thought I would test to see if the headlight bulbs were actually getting power first.


Check the dipped headlight bulb is getting power

The dipped beam headlight harness connector is really easy to access and can be pulled off to access the plug.

To test the lights are getting power:
  1. Turn on the ignition (no need to start the engine) and turn the combination switch so the headlights should be on.
  2. Set your multimeter to measure DC voltage.
  3. The light harness connector only has two terminals. Put the red multimeter probe on one and the black probe on the negative terminal of the battery. You should get a reading of around 11.9v. If you don't get anything, try the other terminal on the headlight harness.
  4. Once you have found which terminal is live, set your multimeter to continuity mode and check the other terminal against the negative terminal on the battery.
If you have 11.9v on live and a solid ground back to the negative terminal of the battery then congratulations, both your bulbs are just blown.

If you don't, then i'm sorry but I can't help you. More investigation would be needed, my first port of call would be checking the combination switch, lots of owners have reported obvious visual damage to the terminals.

Conclusion
Both dipped beam headlight bulbs are blown! Well at least that's an easy fix. I was still curious as to how this could have happened so I did a bit more research which I thought I would share.

1) It is fairly common that both headlight bulbs blow within a short time of each other. The reason behind this is probably that bulbs are made to tightly controlled specifications and so you could assume that under almost identical operating conditions, and in the absence of manufacturing defects, you would expect them to have a similar service life.

2) Many times where people claim both bulbs blew at the same time, what actually happened was one bulb was already blown but they didn't notice until the only remaining bulb went, when it becomes very obvious. This ties in with the above point about headlight bulbs blowing within short periods of each other.

3) The other possibility is that they really did blow at the same time and as the first one went it caused a change in voltage which blew the other one. I have no idea how mechanically sound this theory is but it seems plausible.

The Fix
I can't say I'm best pleased as these bulbs were relatively expensive Osram Nightbreakers which were  only just over 12 months old (and conveniently just out of warranty). After reading some reviews online I decided to get some cheaper Bosch Pure Light bulbs (based on their excellent review by Which?) and I honestly cannot notice the difference between them and the premium Osram's.

2005 Honda Civic Type R bulb type for dipped beam is H1 55W 12V if anyone is wondering.

7 top tips to stop car windows misting up


Fed up of getting into your car only to find the windows are misted/steamed up and you can't go anywhere until they clear? Read on for our top tips on how to prevent this annoying issue from happening in the first place.

1) Check for leaks
Excessive moisture must be coming from somewhere! Check everywhere for leaks and damp patches. Common leaky points are around door seals (especially the bottom), sunroofs, windscreen and boot lids, but also rear lights and rear wheel arches. Also check around the front foot wells and dash in case you have a leaky heater matrix. Don't forget to lift floor mats and carpets.

Feel around these areas with your hands and you should instantly be able to tell if they are damp, especially if it's been raining.

2) Remove moisture with a dehumidifier
A cheap solution is to put a few of those silica gel packets you get inside the packaging of shoes and other products in your door pockets. However, there are specially designed car dehumidifier products such as the Pingi LV-A300 which are available for a few pounds and will do a better job and can be reused as many times as you need!

3) Reduce moisture brought into the car
Even just walking to the car when it's raining can introduce a significant amount of moisture into the inside of your car, by keeping the windows closed (as we generally do when it's raining) this moisture has nowhere to go and will condense on the windows when they drop below the dew point. If you can shake umbrellas and coats off before putting them in the car this will help a bit, also remember to remove them when you get out.

4) Clean the inside of your windows
Dust, oil and grease which naturally builds up on the inside of your car windows (especially the windscreen) effectively increases the surface area which water droplets can cling to. This will not eliminate misting but it will reduce the severity of it, increasing visibility and safety.

Wipe thoroughly with a good quality glass cleaner and clean microfibre cloth.

5) Apply an anti fog coating to the windscreen
There are several products on the market such as Rain-X Anti Fog which are specially designed to prevent condensation forming in the first place. I've not tried this product personally but here is what some customers on Amazon have said:


6) Check your pollen filter
A blocked pollen filter will significantly reduce the amount of air which can circulate in the cabin, meaning damp air cannot escape. If it is really blocked up then all this dirt and gunk will hold moisture from the air as it is drawn through and will not dry out, meaning when you turn on the cabin vents damp air will be drawn into the cabin. Pollen filters are usually very easy to access so check your owners manual for how to do this.

7) Remove damp cloths/demister pads
If you do get any condensation and use a cloth or demister pad to wipe it clean, remove this from the car when you get out and dry it at home or work. If you leave it in the car the moisture will evaporate and end up back on your windows a few hours later. Kind of like a miniature and more annoying water cycle.

Whilst you're working on preventing the issue, try these tips to help clear the moisture quicker:

1) Turn your air conditioning on
Air conditioning removes significant amounts of moisture from the air as part of the cooling process, so if you have working air con, crank it up. This will be the fastest way to clear the condensation.

2) Turn off re-circulate
Most cars have a setting to re-circulate the air in the cabin rather than use fresh air from outside for the heaters. This is great if you're driving past a stinky farm or want to heat up quickly, not so good for clearing away moisture.

3) Open the window
This tends to work best when it's dry outside. Remember you want the warm moisture filled air inside the car to escape, if it's raining and high humidity outside then opening a window will not be very effective. Still, letting the warm air escape should help.

4) Park your car in a garage
This will not only help keep your car out of the rain if the cause is water ingress, but it will also keep the temperature of your windscreen from getting too cold which should prevent condensation forming.

Hope this helps! If you've tried out any of our tips or have something else to add we'd love to hear from you. Please leave your comments below.

Bar Keepers Friend (Brite Power Powder) To Clean Windscreen

windscreen smears
Bar Keepers Friend (now re-branded as Brite Power Powder) is the best product i've found for removing smears/grease/film from windscreens. It's cheap, easy to use, and leaves a perfect smear free finish. Curious? Well then read on to find out more.

What causes windscreen smears?

Windscreen smears are caused by all the general c**p that lands on your windscreen: dirt, grime, grease, car shampoo with wax, old/poorly applied windscreen sealants, tar, oil, diesel fumes etc. The list goes on.

If it's not properly cleaned, this layer of greasy contaminants will build up over years and becomes more and more difficult to remove.

Often, this layer cannot be removed with standard glass cleaning products, no mater how hard you scrub, they just don't have the strength to cut through the baked on layer of grease and grime.

I even tried using a clay bar but this made little impact.

The solution?

I turned to Google and found a LOT of people seemed to be raving about Bar Keepers Friend for cleaning windscreens and other glass.

A quick trip to the local discount store and a couple of quid later I was ready to go.

The active ingredient in Bar Keepers Friend/Brite Power Powder is oxalic acid, which is found in spinach, rhubarb and other green vegetables. When working the powder into the windscreen you can feel it biting, it feels like an abrasive.

The best part about this product is how easy it is to use:
  1. Quickly wash windscreen with water and a sponge to get the worst of the dirt off
  2. Sprinkle the Bar Keepers Friend on a damp microfibre polishing pad
  3. Work the powder into the windscreen in circular motions, with reasonable pressure until the powder has dissolved.
  4. Thoroughly rinse the windscreen with water and a sponge to remove any remnants of the powder. You may also want to rinse the surrounding paint work to ensure non of the diluted powder is left to dry.
In a little over 5 minutes later my windscreen was like new. I also gave the wiper blades a clean/degrease with a microfibre cloth and traditional glass cleaner. At the weekend I think i'll buy some new ones anyway as the passenger side is an inch longer than it should be.

Bar Keepers Friend vs Brite Power Powder

Bar Keepers Friend is the original branding, and there are many threads (like this one, and this one) on the internet raving about how great it is at cleaning windscreens. However, Bar Keepers Friend is now sold as Brite Powder Power. Exactly the same formula, made by the same people. Just with a different label on the bottle. I was told this by more than one store assistant when trying to find Bar Keepers Friend.

Conveniently, Bar Keepers Friend is also great at cleaning oven glass, stainless steel, porcelain sinks, showers, BBQ grills and loads more around the house.

Results

I honestly can't fault this product. It's cheap, easy to use, extremely effective and you can use it elsewhere around the house.

Where to buy

This product is reported to be available at many supermarkets and discounters e.g Wilko. However, I just bought mine from Amazon.


Have you used this product? Please leave your comments below with your feedback.

10 Gifts For Petrolheads (That they actually want)

Looking for a gift for a petrolhead but feeling a bit lost in the world of oil, horsepower and turbos? Luckily for you, i'm a petrolhead/car enthusiast and i've put together this list of the best gifts for petrolheads of all ages starting from under £10.


1. Haynes Build Your Own V8 Engine

Unfortunately, many petrolheads will not get the chance to have a real v8 engined car sat on the drive. So why not give them the opportunity to build a fully working miniature version instead? This literally is a fully functioning scale model of an engine, with over 250 pieces including camshafts, pistons, valves, cambelts and all that other cool stuff - guaranteed to keep the car geeks and engineers amongst us occupied for hours. Aside from taking apart a real engine, this must be the best learning tool for younger petrolheads to understand how an engine works. Available on Amazon from £32.66.

2. Auto Glym Perfect Bodywork & Wheels Car Cleaning Kit

I would bet money every petrolhead already has at least one Auto Glym product in their garage because Auto Glym are a well respected brand within the professional car cleaning industry who offer great products at a reasonable price.

This complete car cleaning kit contains 6 of their best products which compliment each other to get amazingly clean bodywork and wheels. This car cleaning kit is the perfect gift for any motoring enthusiast. Available to buy on Amazon from £26.71.

3. FUEL: The Worlds Smallest Phone Charger
This tiny little emergency phone charger carries just enough power to charge a phone for around 20 - 30 minutes. Designed in the shape of a fuel can, the nozzle is removed to reveal a male micro-USB connection which can plug straight into your phone's charging socket. Genius! Available on Amazon from £22.68.


4. Swarfega Orange Rapid Hand Cleaner
"Hand cleaner?!" I hear you say. Well this isn't just any old hand cleaner my fellow readers - it is the ultimate companion for working on cars or motorbikes. Swarfega is specially designed  for removing oil, grease and all that other nasty grime which you've probably seen your car enthusiast friend struggling to scrub off with normal hand soap. As an extra bonus it has a lovely orange fragrance. Doing an oil change has never smelled so good. Available on Amazon for just £6.75.

5. Spanner Bottle Opener
The humble bottle opener is a gift which never goes unused. This high quality, stainless steel bottle opener has a fully functional 14mm open ended spanner on the other end. Comes in a retro gift box with a lid. Perfect for car or bike enthusiast, mechanic or avid DIYer. Available on Amazon for £16.39.

6. Brunton Torpedo 2600 Portable Battery
A life saver for anyone who's ever been caught out with a phone which has run out of charge. This little portable battery by Brunton is just 13cm long but carries enough power to fully re-charge most smartphones. It can also be used to charge MP3 players, cameras and anything else which charges via a USB cable. Keep this in your glove box and never run out of phone battery again. The best bit is it recharges by plugging straight into the 12v cigarette lighter socket of your car. Available on Amazon for £34.99.


7. Artistic Car Print
A stylish print of their favourite car is a great gift for any petrolhead. and if they are lucky they might even be able to display it in the house. If not, it will surely find a special spot in the garage where they can admire it whilst working on their car. The above example is the famous Group B Audi Quattro rally car, and there's hundreds more on Not On The High Street.


8. Complete Guide To Garages Book
"Ideas and inspirations for creating the perfect garage" - Sounds like every petrolheads dream come true. The garage is the petrol heads natural environment, so why not buy this guide to help them make the best garage imaginable! Maybe more of a fantasy for most but everyone likes to play the "if only" game. Also available on Kindle. Available on Amazon for £16.99 (paperback).

9. Retro Castrol Motor Oil Mug
Castrol has some serious heritage, it was founded in 1899 and the brand is immediately recognised by petrol heads of all ages for it's long-standing association with all sorts of motorsport, from rallying to Formula 1 and everything in between. This retro style mug has the classic vintage Castrol Motor Oil logo on the side and is made from enamelled tin. Perfect for the home or drawing the envy of your colleagues for professional mechanics. Available on Amazon for £8.10, bargain!

10. Roadcraft: The Police Drivers Handbook

Roadcraft is the go-to book for motoring enthusiasts looking to improve their driving skills and safety. Focusing on many different factors including increase awareness, foresight, vehicle handling, and reading road conditions, this book contains a wealth of knowledge any petrol head would love to read about. Available on Amazon for £11.89.

I hope you enjoyed this list of Christmas gift ideas for petrolheads, as I said at the start, i'm an out and out car enthusiast and if santa got me any of these gifts i'd be a happy man.

Disagree with me? Products out of stock on Amazon? Any comments welcome below.

Which is best: 205/45/17 vs 215/40/17 tyres?


Like many petrol heads, I understand how fundamental tyres are to how a car handles and changing tyres is something I like to think carefully about. When my Honda EP3 Civic unexpectedly failed it's MOT on two misshapen rear tyres I was faced with a tough decision - replace just the two rear tyres in the same size (215/40/17) or buy a complete set and swap back to the OE size of 205/45/17.

It was only after owning the Civic for several months and feeling a bit unhappy at how harsh the ride was, that I realised the previous owner had put wider, lower profile 215/40/17 tyres on. I imagine that on silky smooth roads or on a track this profile of tyre would be beneficial but on UK roads I found the ride too crashy and it felt like there was not enough compliance to deal with the bumps and imperfections in the road, with the result being less grip and an uncomfortable ride. I also felt the low profile tyres were contributing to tramlining.

Previously owning a Peugeot 306 GTI-6 (which I directly compared to the Type R in this review), I'm a big fan of what would now be considered van tyres. The 306 used to run 195/55/15 tyres and they were bloody brilliant, it would eat up a bumpy B road like nothing else and speed bumps could be taken at a decent speed without that horrible feeling that you are going to blow a damper.



With this in the back of my mind, I took the plunge and purchased a set of Bridgestone Potenza RE050A in 205/45/17 from BlackCircles.com. If you are wondering, the previous tyres were Falken FK 452, which have a pretty good reputation online.

The difference was night and day - the higher profile tyres gave much more compliance and increased ride comfort considerably. Confidence and grip were also vastly improved, although some of this would have undoubtedly been due to the new tyres. Road noise was also reduced but I don't know if this is due to the tyre profile change or different model of tyre.

In my opinion, the ride on the Honda Type R is stiff enough without having to drop to a lower profile to get increased control and I would strongly recommend sticking with the tyre size that Honda intended when they designed the car.